Repairs, new runs and re-tagsPermit and inspection, not a handshakeAppliance controls left to the appliance trade
Gas work is measured, pressure tested and inspected, in that order, because none of it can be judged by eye. Clark County issues a gas re-tag permit start to finish online with no plan review.
Figures above are published third party data, not company claims. Sources: Clark County Building and Fire Prevention, Nevada State Contractors Board, NRS 624.031.
Gas line work covers the piping between the meter and an appliance: repairs, new runs, valves, sediment traps and pressure testing. Clark County issues a gas re-tag permit online with no plan review. That is what a homeowner needs after the utility locks a meter off. If you smell gas now, leave the building and call from outside.
This page covers gas line services across the Las Vegas Valley. If you are not sure this is the right service, start from every service we cover.
Gas calls come from three directions: something smells, something new needs connecting, or the utility has shut the meter down and left a tag.
Read the safety note first. Everything else on this page can wait, and a gas smell cannot.
If the question is about the pipe, the valves, the connectors or the pressure test, this is the right page. That runs from the meter to the appliance shutoff.
It also covers sizing, meaning the calculation of whether the existing pipe can carry the load you want to add to it.
If the appliance itself is faulty, the burner, pilot assembly or control board is the issue. That belongs with the manufacturer or an appliance service company.
If the real question is replacing a gas water heater, the permit and the work are different. Start at water heater installation across Clark County or tankless Water Heaters in the Las Vegas Valley.
Gas piping is a closed system that has to prove itself under pressure. Every category below ends the same way, with a test and a jurisdiction sign off.
| What is included | What that means |
|---|---|
| Leak locating and repair | The system is isolated and pressure tested section by section until the failing run is identified, then that section is repaired or replaced. |
| New appliance runs | A branch is taken from the existing system to a range, dryer, pool heater or fire pit. It is sized for the load it carries. |
| Meter re-tag test | After the utility locks a meter off, the house side piping is pressure tested and inspected so the meter can be turned back on. |
| Sizing calculations | Pipe capacity is calculated against the total appliance demand, which is what decides whether an existing line can take a new appliance. |
| Sediment traps and shutoffs | A drip leg and an accessible appliance shutoff are fitted where they are required, so each appliance can be isolated on its own. |
| Connector replacement | Old or damaged flexible appliance connectors are replaced with current rated connectors when an appliance is moved or renewed. |
| Capping abandoned lines | A line left over from a removed appliance is cut back and capped properly, rather than left live behind a wall or a cabinet. |
Gas is the one category where being clear about limits matters more than selling.
Safety, then paperwork, then pipe, then proof.
If gas is escaping now, leave the building and call the gas utility and 911 from outside. Do not search for the leak yourself and do not use switches on the way out.
Immediately, before any bookingYou confirm the address and the appliances involved. The permit type is identified with the building department, and the demand of every appliance on the system is added up.
Before any work startsYou keep people and pets away from the work area. Gas is shut off at the meter or the branch, the pipe work is done, and the appliance shutoffs are fitted.
On the dayThe system is put under test pressure and watched, then presented to the inspector. The gauge, not an opinion, is what says the work is sound.
Before the gas goes back onAppliances are brought back into service in order. You are shown the shutoff for each one, along with the main valve at the meter.
At handoverThe price is fixed when you approve the scope, after the sizing and permit check. Pipe size and permit type are what the number is built from.
The table carries published market ranges for gas repair and new gas runs, from national cost guides. They are market context and not a quote from this company.
Gas is one of the few categories where published ranges spread very wide. A joint you can see and a leak inside a wall are different jobs.
Estimating gas work starts with the load and the route. The appliance demand is added up, the existing pipe size is measured, and the path for any new run is walked.
Permit fees and the inspection are part of the number and are stated separately. You can see what is work and what is jurisdiction cost. The price is agreed before anything is cut.
| Job | Typical Las Vegas range | What moves the number |
|---|---|---|
| Gas line repair | $120 to $760 | A simple joint leak runs $120 to $250, a leak inside a wall $270 to $760, a buried line $1,500 to $5,000. |
| Gas line installation | $272 to $936 | Average about $598, or $15 to $30 per linear foot for a new run. |
| Service call or diagnostic fee | $75 to $150 | The broader trade range runs about $50 to $200. Emergency and after hours dispatch is higher, commonly $150 to $350 or more. |
| Tankless water heater, installed | $1,406 to $3,902 | National average about $2,640. Gas line sizing and venting are the two things that move it most. |
Every figure in this table is a published Las Vegas or national market range from the source named beside it. It is not a quote and it is not this company's price list. Your number comes from the on site estimate. Sources: <a href="https://www.homeadvisor.com/cost/plumbing/" rel="nofollow noopener" target="_blank">HomeAdvisor cost guides, 2026</a>, <a href="https://www.housecallpro.com/resources/marketing/how-to/how-to-price-plumbing-jobs/" rel="nofollow noopener" target="_blank">Housecall Pro 2026 Plumbing Price Guide</a>.
Repairing one failed section costs far less than re-running a line, so replacement is reserved for pipe that is corroded throughout or undersized.
The published trade figure for a service or diagnostic visit is roughly $75 to $150. It comes from the Housecall Pro 2026 Plumbing Price Guide, which puts after hours dispatch above that.
No fee or credit policy has been verified for this business, so none is stated here as fact. What the call costs, and whether it is credited toward the work, is confirmed with you before anyone is dispatched.
Ranges last reviewed September 2026.
Two appliances drive most residential gas questions in the valley, and both of them change what the pipe has to carry.
A tankless water heater fires at a much higher rate than a storage tank, so the existing line often cannot feed it. Cost guides put tankless installation well above tank installation, and gas line sizing with venting is what moves that figure most.
A tank water heater is the quieter gas appliance, drawing less at a time but needing its own shutoff, connector and sediment trap. Clark County requires a permit for a water heater replacement, and says whoever pulls that permit is responsible for the installation.
Photographs here are generated illustrations of the conditions described, not work by this company, with real job photographs added as they are approved.
No. If you can smell gas, leave the building and call the gas utility and 911 from outside, away from the property.
The utility responds to a suspected leak as an emergency and can shut the supply at the meter. Booking a plumbing appointment is the wrong next action.
Nevada's small job exemption stops at $1,000, and it does not apply when a permit is required or to work a plumbing contractor performs.
The bigger issue is the test. A connection that seems fine can leak slowly, and the only way to know is a pressure test on the system.
A tankless unit demands far more gas at once than the tank it replaces. The existing branch often has to be upsized to feed it.
Cost guides list gas line sizing and venting as the two things that move a tankless installation price the most. That is a sizing fact, not an upsell.
Check it yourself, free, on the Nevada State Contractors Board public search. You can look up a license number, a company name or a principal.
This site publishes no license number, because none has been verified for this business yet. Ask for one and check it before gas work is done.
Not until the house side piping has passed a test. That is the purpose of the gas re-tag, and Clark County issues that permit fully online with no plan review.
The sequence is fixed: pressure test, inspection, then the utility restores service. Skipping a step simply means the meter stays off.
We cover gas line services in every part of the valley listed below. Each area page names the office that issues the plumbing permit there and who owns the sewer line at the curb, because both genuinely differ from one city to the next.
Say it is about this when you call and you skip the sorting.
We are a service area business. We come to you, so there is no counter to visit and no street address on this page. The number above is the fastest way in.
About a minute of detail changes what we can tell you on the call.
A re-tag is the process of getting a gas meter turned back on after the utility has locked it off. The house side piping has to be pressure tested and inspected first. Clark County issues the gas re-tag permit start to finish online, with no plan review, one item per permit.
Meters are commonly tagged off after a suspected leak, a long vacancy, or work that interrupted the system. The tag stays until the inspection clears it.
Leave the building straight away and take everyone with you. Call the gas utility and 911 from outside, well away from the property. Do not hunt for the leak and do not operate light switches or garage doors. Do not go back in until you are told it is safe.
Everything else waits. Plumbing work on the system starts after the utility has made the property safe.
Gas piping work is permitted work, and the re-tag itself has its own permit type issued online by Clark County. The small job exemption in Nevada law does not help here, because it explicitly does not apply where a building permit is required.
Other valley jurisdictions issue their own permits. The department covering your address is identified before the job is priced.
A storage tank heats water slowly over time, while a tankless unit heats it the instant you open a tap. That means a much higher burner rate, and the pipe has to deliver that volume without starving other appliances on the same system.
Published cost guides identify gas line sizing and venting as the two biggest drivers of a tankless installation price.
A sediment trap, sometimes called a drip leg, is a short capped length of pipe below the connection to an appliance. Debris and moisture traveling through the line drop into it instead of reaching the appliance valve. It is a small piece of pipe that protects an expensive control.
Where code requires one, an inspector will look for it. It is one of the most common items found missing on older installations.
The system is isolated from the meter and the appliances, then charged with air to a set test pressure. It is watched on a gauge for a set period. A pressure that holds proves the piping. A pressure that falls proves there is a leak somewhere in the section under test.
Isolating section by section then narrows down where that leak is, which is why a hidden leak costs more to find than to fix.
Usually yes, and it is a common request in valley backyards. The deciding factor is capacity. Every appliance already on the system is added up against the size of the existing pipe before a new branch is designed. The calculation happens before any pipe is ordered or any route is chosen.
Outdoor runs also have their own requirements for burial depth, materials and shutoff placement, which the inspection checks.
Use the Nevada State Contractors Board public license search. It is free to use, and you can search by license number, company name or principal name. The result shows which classifications that license holds, and whether the license is currently active.
Plumbing sits under the C-1 classification, plumbing and heating contracting, with C-1d covering plumbing specifically. The check takes about a minute.
Describe what is happening and we will tell you what it usually takes to fix.