Sinks, valves, bibbs, laundry boxes2024 Uniform Plumbing Code with local amendmentsPermit status checked for your address
Fitting a fixture is half plumbing and half measurement, because the new thing has to meet piping that was placed years ago. About 47.3 percent of Clark County homes were built in 2000 or later, and their rough-in dimensions are not the same as an older house.
Figures above are published third party data, not company claims. Sources: US Census ACS, InterNACHI, Clark County Building and Fire Prevention.
Fixture installation means connecting a new sink, valve, tap, bidet seat, hose bibb or laundry box to piping already in the wall or floor. The work splits into rough-in, where pipe is moved, and trim out, where the visible part is fitted. Moving concealed piping is what turns a simple swap into permitted work.
This page covers plumbing fixture installation across the Las Vegas Valley. If you are not sure this is the right service, start from the full list of what we do.
Fixture work usually starts with a purchase, a remodel or a part that has given up. Almost none of it starts with an emergency.
These are the reasons people call about fitting something new. Each one has a different amount of pipe work hiding behind it.
If you are putting something new in and the pipe is already there, this is the right page. That includes fixtures you bought yourself.
It also covers the valve behind the wall. That includes a tub and shower mixer, a laundry box or an exterior hose bibb.
If the supply piping through the whole house is failing rather than the fixture, fitting new trim will not help. That is whole Home Repiping in the Las Vegas Valley or pipe Repair in Clark County, NV.
A water conditioning system is a separate job with its own rules, because unincorporated Clark County requires a permit and an inspection for one. Start at water Softener Installation in Las Vegas.
Every fixture in a house is a joint between something visible and something buried. The visible half is quick. The buried half is where the time and the permit questions live.
| What is included | What that means |
|---|---|
| Tub and shower valves | The mixing valve behind the wall is replaced, which normally means opening tile or accessing from the back, then pressure testing before it is closed. |
| Sink and vanity sets | The tap, the pop up drain, the tailpiece and the trap are fitted together, because a new basin usually changes the height of the outlet. |
| Angle stops and supply lines | The shutoff valves and flexible connectors are replaced during the fitting, since disturbing an old stop is what makes it leak later. |
| Hose bibbs and exterior taps | Outdoor taps are replaced at the wall, and the connection behind the siding or stucco is the part that decides how long the job takes. |
| Laundry boxes | The recessed box holding the hot, cold and drain connections behind a washer is replaced when it rusts, stains or the valves seize. |
| Bidet seats and toilet connections | A supply tee and the correct stop are fitted behind the toilet so the seat has its own controlled feed rather than a shared hose. |
| Pot fillers and bar sinks | A new run of pipe is taken to a location that never had one, and this is the category most likely to need a permit. |
Four things that are checkable rather than promised.
Measurement and permit status both come before any wall is opened.
You describe or photograph the fixture and the space. The spec sheet for a fixture carries its rough-in dimensions, and that document decides whether the existing pipe will meet it.
On the phoneYou do nothing here. The jurisdiction covering your address is identified, and whether the work needs a permit is confirmed with that building department before a price is given.
Before the quoteYou clear the work area and agree where access will be taken. Water is shut at the nearest working valve, the fixture is fitted, and connections are made to the existing stub-outs.
On the dayAny concealed connection is tested under pressure while it is still visible. Nothing gets tiled, patched or covered until that test has held.
Before the wall is closedHandles, diverters and stops are all operated in front of you. You are shown which valve isolates the new fixture if it needs shutting off.
At handoverThe price becomes final when the scope is approved after the permit check, since permitted work and exempt work are not the same job.
The ranges here are published market figures for the common fixture jobs, from national cost guides. They are not this company's rate card.
Fixture labor varies more than almost any other plumbing work, because two sinks that look alike can hide very different piping behind them.
Estimating a fixture job means looking at both ends: the fixture you have chosen and the pipe that has to meet it. That usually means opening a cabinet or an access panel.
Where a wall has to be opened, the estimate says so before work starts, along with who is responsible for closing it. The price is agreed with you first.
| Job | Typical Las Vegas range | What moves the number |
|---|---|---|
| Kitchen faucet replacement | $162 to $364 | Average about $262, with a full range of $91 to $600. |
| Toilet installation | $224 to $533 | Average about $374, not counting the toilet itself. |
| Garbage disposal replacement | $200 to $625 | Average around $550 including the unit. |
| Service call or diagnostic fee | $75 to $150 | The broader trade range runs about $50 to $200. Emergency and after hours dispatch is higher, commonly $150 to $350 or more. |
Every figure in this table is a published Las Vegas or national market range from the source named beside it. It is not a quote and it is not this company's price list. Your number comes from the on site estimate. Sources: <a href="https://www.homeadvisor.com/cost/plumbing/" rel="nofollow noopener" target="_blank">HomeAdvisor cost guides, 2026</a>, <a href="https://www.housecallpro.com/resources/marketing/how-to/how-to-price-plumbing-jobs/" rel="nofollow noopener" target="_blank">Housecall Pro 2026 Plumbing Price Guide</a>.
Fitting a new fixture onto sound existing pipe is a small job, while relocating that pipe for a new layout costs several times more.
A service or diagnostic visit is published across the trade at about $75 to $150. The source is the Housecall Pro 2026 Plumbing Price Guide, with higher figures outside normal hours.
No verified fee or credit policy exists for this business, so this page publishes none. The visit charge, and whether it comes off the installation, is confirmed with you on the call before anyone is dispatched.
Ranges last reviewed September 2026.
The visible fixture is the last small part of the job. These two pictures show the parts that decide how it goes.
Copper is still common in valley homes built through the 1990s, and InterNACHI credits a copper water line with about 50 years. Working on it means heat, clean joints and a pressure test. Nothing gets closed up until that test holds.
Newer construction and most repipes use PEX, credited with a 40 to 50 year life. It bends around obstacles, so a new fixture location can often be reached without opening as much wall. The trade off is that connections must be made with the correct fittings for the system.
Photographs here are generated illustrations of the conditions described, not work by this company, with real job photographs added as they are approved.
Yes. Send the model number or the spec sheet beforehand so the rough-in dimensions can be checked against what is in your wall.
The maker coverage on a fixture you bought is a matter between you and that manufacturer. This site makes no promises of that kind about the work.
Sometimes you do not. Clark County Code 22.02.195 exempts repairing leaks in pipes, valves or fixtures, as long as concealed piping is not replaced or rearranged.
The exemption stops the moment the pipe behind the wall is changed. That is why the department for your address gets asked before a price is quoted.
A tub and shower mixer lives inside the wall, connected to hot, cold and the riser. There is no way to replace the body of that valve from the front.
Where a home has a rear access panel in the neighboring closet, the wall can often be left alone. That gets checked before anything is cut.
It changes the approach rather than blocking it. Galvanized supply pipe was common from the 1920s through the 1950s and has a 20 to 30 year life.
Old threaded galvanized can crack rather than unthread. In neighborhoods like Huntridge, built 1941 to 1944, that possibility is discussed before work starts.
That split is normal on remodels, and plenty of homeowners handle the visible parts. Be clear about it up front so the rough-in is left ready for you.
Nevada does exempt small jobs under $1,000, but not where a permit is required, and not for work of a type a plumbing contractor performs.
We cover plumbing fixture installation in every part of the valley listed below. Each area page names the office that issues the plumbing permit there and who owns the sewer line at the curb, because both genuinely differ from one city to the next.
Say it is about this when you call and you skip the sorting.
We are a service area business. We come to you, so there is no counter to visit and no street address on this page. The number above is the fastest way in.
About a minute of detail changes what we can tell you on the call.
A fixture is anything that delivers or receives water at a fixed point. That means sinks, basins, tubs, showers, toilets, bidets, laundry boxes, hose bibbs and pot fillers. The pipe feeding it and the drain taking water away are not fixtures. They are the rough plumbing behind it.
The distinction matters for permits. Swapping a fixture is usually exempt work, while changing the pipe behind it usually is not.
It depends on whether concealed piping moves. Clark County Code 22.02.195 exempts repairing leaks in pipes, valves and fixtures, and removing and reinstalling a toilet. The condition is that concealed piping is not replaced or rearranged. Adding a fixture where none existed is a different question and needs the department to answer it.
Each jurisdiction runs its own counter. Unincorporated areas go to Clark County on West Russell Road. Henderson, North Las Vegas, Boulder City and the City of Las Vegas each have their own.
The valley is on the 2024 Uniform Plumbing Code. Clark County applies it to applications filed from January 11, 2026, and the City of Las Vegas from January 5, 2026. It is not the plain code book, because jurisdictions enforce it with the Southern Nevada Amendments.
Those amendments are written by the Southern Nevada Building Officials. They are the reason a detail acceptable elsewhere can be handled differently here.
Yes, and many people prefer to, because fixtures are a design choice as much as a plumbing one. The useful step is sending the spec sheet in advance so the rough-in dimensions can be compared with the piping you already have.
Order the matching valve body where a brand sells the trim and the valve separately. That mismatch is the most common delay on shower jobs.
A faucet sits on top of a counter and connects to two flexible lines you can reach from the cabinet. A shower valve sits inside the wall and connects to three rigid pipes. Reaching it means opening a finished surface, and closing that surface is its own trade.
The pressure test also belongs to a shower valve job. A concealed joint is tested before the wall closes, which adds time to the visit.
Rough-in is the pipe work done before the wall is closed: supply lines, drains, vents and valve bodies in their final positions. Trim out is everything fitted afterward, meaning the handles, spouts, escutcheons, seats and visible fixtures that the homeowner actually sees and touches.
On a remodel the two are usually separated by weeks of tile and drywall work, so the schedule for each is agreed at the start.
Usually, with an adapter at the connection. The complication is almost always the pipe material itself. Galvanized steel was standard from the 1920s through the 1950s. Neighborhoods such as Scotch 80s, which filled in through the 1950s, still have it in places.
Galvanized corrodes from the inside out, so a stub-out can look fine and be nearly closed. That is checked before a new fixture is fitted to it.
Either can, and it matters because the permit holder is the responsible party. Clark County states that for a water heater replacement, whoever pulls the permit is responsible for the installation. That is the clearest published example of how the rule works in practice.
Nevada also allows an owner to pull permits for their own residence with an Owner-Builder Affidavit of Exemption, which requires direct supervision of the work.
Describe what is happening and we will tell you what it usually takes to fix.